|
Main / Optical interfaces / PORC-3232
| PORC-3232 series SDIembedded optical receiver with synchronization, auxiliary audio input and bidirectional RS-232/RS-422 support |
PORC-3232 optical receivers convert an optical signal into electrical, support SDIembedded synchronization to the REF, auxiliary audio input. PORC-3232 supports the bidirectional RS-232/RS-422 communication over an optical link. PORC-3232 module occupies two slots in the PROLFEX 1U/3U racks.
Model |
Analog audio inputs |
AES/EBU audio inputs |
Rack slots occupied |
| PORC-3232AA |
4 |
- |
2 |
| PORC-3232AE |
2 |
1 |
2 |
| PORC-3232EE |
- |
2 |
2 |
Features
- signal loss indication
- embedded audio present indication
- SDI synchronization to the REF (black burst)
- built-in 1kHz test-tone generator
- up to four audio channels emdebbable
- audio group selection for embedding and deembedding
- audio gain controls ±6dB with 0.2dB steps
- audio delay follows video
- adjustable (±32 frames) audio delay
- analog or AES/EBU audio input
- EDH (min/hour) indication
- PAL MON video output with the bar-graph audio level meters (quasi-peak and VU) OSD
- bidirectional RS-232/RS-422 data up to 150 kbps
- WDM/CWDM optical systems compatibility
- 24-bit audio ADC
Technical specifications
- Inputs
- Optical input
| Number of inputs |
1 |
| Photodiode |
InGaAs/InP PIN diode |
| Optical sensitivity band |
1100~1650nm |
| Optical sensor diameter |
120µm |
| Optical connector type |
FC/PC |
| Maximum input optical power |
0dBm |
| Optical dynamic band |
-25 ~ -3dBm |
- Analog audio inputs
| Connector type |
DB-15 |
| input impedance |
>10 kOhm |
| input type |
balanced |
| 0dB FS input headroom |
+18dB |
| Dynamic range |
100dB |
| Distortions and noise |
less than 0.006% |
| ADC |
24 bits, 20 MSB embedded |
| Sampling rate |
48kHz |
- AES/EBU audio inputs
| Connector type |
DB-15 |
| input type |
transformer balanced |
| Amplitude |
0.2~4.0V |
| input impedance |
110 Ohm |
| maximum input cable length |
up to 100m |
- REF video input
| Input |
AC-coupled |
| Connector type |
BNC |
| Composite SYNC amplitude |
300±100mV |
| Input impedance |
>10kOhm |
- Outputs
- SDI video output
| Number of outputs |
3, with reclocking |
| Compatibility |
ITU-R BT.656 (embedded audio) |
| Connector type , output impedance |
BNC, 75 Ohm |
| Return loss |
better than 18dB at Ft |
| Amplitude |
800mV±10% |
| Audio gain controls |
±6dB with 0.1dB steps |
- PAL monitor output
| Connector type |
BNC |
| Amplitude |
1000±20mV at 75 Ohm |
| DAC |
10 bits |
| Frequency response |
<3dB up to 5.5MHz |
- Optical output (RS-232/RS-422 data return channel)
| Optical system (model index) |
WDM (PORC-3232) |
PORC-3232D |
CWDM (PORC-3232DCW##) |
| Laser diode type |
FP |
FP |
DFB |
| Laser wavelength |
RX 1310±20nm, TX 1550±20nm |
1310±20nm (1550±20nm by request) |
1270~1610nm in 20nm steps |
| Optical output power |
-3dBm |
-3dBm |
0dBm |
| Optical connector type |
FC/PC |
FC/PC |
FC/PC |
| Number of optical fibers |
1 |
2 |
2 |
- RS-232/RS-422 data input/output
| Connector type |
DB-15 |
| Standard compliance |
RS-232 |
| Data rate |
up to 150 kbps |
Frame/Line synchronization of SDI to REF:
- ±127 TV lines advance/delay within one TV frame
- ±32µs advance/delay within one TV line with 37ns steps
PORC-3232 general description
Simplified schematics
Optical signal is amplified and demodulated. The resulting SDI is decoded into the 10-bits 4:2:2 stream which is processed to recover video and audio. Video stream is buffered and synchronized to the REF signal. The deembedded audio is buffered and a user-controllable delay is applied. The 2:1 multiplexer selects which audio source is reembedded into an output SDI - either the one from the input SDI or the one from external AES/analog inputs. RS-232/RS-422 data is deembedded from an input optical signal, the return RS-232/RS-422 channel is embedded into the output optical signal. The monitor video output provides the PAL picture with the audio level meter OSD.
PORC-3232 rear panel:
Controls and indicators
PORC-3232 frontal panel:
The operation mode is selected by toggling the MODE button, the editing is done by pressing the UP and DOWN buttons. Pressing the UP and DOWN buttons simultaneously resets a parameter to a default value. The FREEZE button controls the "frame freeze" function.
The editable modes are:
- INP GROUP SEL - to select an audio group number for deembedding
- OUT GROUP SEL - to select an audio group number for reembedding
- AUD SOURCE - the audio source selection for embedding: the deembedded from SDI or from the external inputs
- TON - 1kHz test-tone generator ON/OFF in a selected audio channel
- VU METR - an audio bar-graph OSD placement and scale controls
- GAIN 1/2 - gain controls in the first stereo pair
- GAIN 3/4 - gain controls in the second stereo pair
- TIMING H - SDI to REF synchronization within a TV line
- TIMING V - SDI to REF synchronization within a TV frame
- TIMING AUD DELAY - audio delay in TV line increments
- FREEZE - the "frame freeze" mode ON/OFF
The indicators:
- REF – lit if there is a valid REF video signal
- INP - lit if there is a valid input video signal
- AUD DET – lit when an input signal contains valid audio packets
- EDH MIN/HOUR – lit if an EDH error was detected whithin the last minute/hour interval
- ADVANCE - displays the current value of delay/advance of SDI signal relative to the REF
The remote control and management from a PC
All the “PROFLEX” modules are remote controllable from a PC. This facility is available if a rack is fitted with a CPU module (ordered separately). |
